TEAC Data Recorder site
TEAC Data Recorder site

Specifications

Main Unit

Sampling Frequency
LX-110/LX-120 Standard		96/48/24/12/6/3/1.5kHz (Common to each channels)
Low Speed SamplingCut-off frequencyAttenuation
1kHz400Hz-80dB(at 500Hz)
500Hz200Hz-80dB(at 250Hz)
200Hz80Hz-80dB(at 100Hz)
100Hz40Hz-80dB(at 50Hz)
50Hz20Hz-80dB(at 25Hz)
20Hz8Hz-80dB(at 10Hz)
10/5/2/1Hz4Hz-80dB(at 5Hz)
2/5/10/30/60s (Cycle)4Hz-80dB(at 5Hz)
(Aliasing may occur under 5Hz sampling frequency)
Sampling Frequency
LX-120 only		102.4/51.2/25.6/12.8/5.12/2.56/1.28kHz
65.536/32.768/16.384/8.192/4.096/2.048/1.024KHz
100/50/20/10/5/2/1kHz (Common to each channels)
Tachometer Pulse Input
LX-120 only		(Cannot be used simultaneously with generator output)
Number of Input
channels		16bit 2 channels, 32bit 1 channel
Only 1 channels support in case of highest sampling frequency
LSB is used for pulse timing
InputThreshold Level +0.5/1/2.5/10/20V
Max. Input Voltage 50V
Input ConnectorBNC
Frequency Division Ratio1 to 255
Moving Average1 to 16
ModePulse count(Gate, Accumulate), Cycle, Frequency, rpm
Generator Output
LX-120 only		(Cannot be used simultaneously with tachometer pulse input)
Output channel1 channel (Same Connector is used with Monitor Output)
Output signalSine, Sweep sine, Pulse, Pink noise, White noise
Input Channels2/4/8/16/24/32ch selectable
Recording MediaSelect [Internal Memory] [Internal Memory + PC card]
Internal Memory64MB Expandable up to 576MB
PC cardPCMCIA TypeII memory card(up to 32GB),
Compact Flash(CF) card (FAT16 or FAT32)
*Ask to sales for support PC card
*It is possible to record data to HDD in computer directly via FireWire
InterfaceSelect 100BASE-TX or FireWire(IEEE1394) (Select to order)
Contact switch controlREC, FWD, REC FWD, STOP, PAUSE, EVENT, PLOCK
Monitor Channel1 (Analog output), BNC
Monitor Output level±1 to 5V, 0.1V step
Microphone Jack1
Loudspeaker / Earphone jack1 each
Max. Recording rateInternal MemoryApprox. 1.6MB/sec.
PC cardApprox. 0.8MB/sec.
PC throughputIEEE1394Approx. 1.6MB/sec.
EthernetApprox. 1.6MB/sec.
Clock accuracy±1ppm (25deg C)
Clock adjustment±30 seconds adjustment
Operation environmentOperation temperature0 to 45deg C
Operation Humidity10 to 80%RH Non-condensing
Safety / EMICE, VCCI
VibrationMIL-STD-810E fig 514.4-1.2..3
Power ConsumptionLX-110DC Amp.Input8ch30W
16ch36W
32ch48W
IN/OUT8ch36W
16ch48W
PA Amp.Input8ch35W
16ch46W
32ch66W
IN/OUT8ch46W
16ch66W
Strain Amp.Input8ch40W
16ch56W
32ch86W
IN/OUT8ch56W
16ch86W
LX-120DC Amp.Input8ch36W
16ch42W
32ch56W
IN/OUT8ch42W
16ch56W
PA Amp.Input8ch41W
16ch52W
32ch76W
IN/OUT8ch52W
16ch76W
Strain Amp.Input8ch46W
16ch62W
32ch92W
IN/OUT8ch62W
16ch92W
PowerDC11 to 30V
Dimension (W x H x D)Approx. 11 13/16" x 2 9/16" x 7 7/8"
Approx. 300mm x 65mm x 200mm
*When expansion Box is attached (32ch, 16ch IN/OUT), Height Approx. 105mm
WeightLX-110Input8ch8 1/4 lb3.7kg
16ch8 5/8 lb3.9kg
32ch13 1/2 lb6.1kg
Input / Output8ch8 5/8 lb3.9kg
16ch13 1/2 lb6.1kg
LX-120Input8ch8 1/4 lb3.7kg
16ch8 7/8 lb4.0kg
32ch13 1/2 lb6.2kg
Input / Output8ch8 7/8 lb4.0kg
16ch13 1/2 lb6.2kg
Standard AccessoriesDC Power cable, LX Control software (LX-Navi),
Operation manual
LX Navi Support OSWindows XP, Vista, 7

Input Amp. DC Amp. AR-LXDC100

Input formatUnbalance
Input couplingDC
Input impedance1M ohm
Input range
(Over range ±127%)		±0.5/1/2/5/10/20/50V
Max. Input voltage±100V
Anti-aliasing filterAnalog filter + Digital filter
LPF-
Frequency bandwidthDC to (Sampling Frequency/2.4), ±0.5dB
A/D bit16/24 bit
A/D conversion method128 times over sampling Delta-sigma method
(64 times over sampling, in case of Max. sampling frequency)
Non-linearity< ±0.1%
DistortionSampling Frequency (fs)FrequencyDistortion
96kHz20kHz< ±0.1%
48kHz10kHz< ±0.07%
24kHz以下fs/4.8< ±0.4%
Range accuracy< ±0.1%
SNR
(16/24 bit)
(25 deg C)		Input rangeBand-widthSNR
< 20VWithin band-width84/94dB
20V80/88dB
SNR is a difference of noise level for 100% of each input range.
Dynamic range is the greatest input level and a difference of noise level of each input.
Dynamic range = SNR + 2 dB
CrosstalkInput rangeBandCrosstalk
ALL20kHz-82/-88dB
< 40kHz-80/-86dB
Inter-channel phase difference< 1 deg (< 20kHz), < 3 deg (< 40kHz)
Input connectorBNC

Input Amp. PA Amp. AR-LXPA100

Input formatBalance / Unbalance
Input couplingBalance DC / Balance AC / Unbalance DC
Input impedance1M ohm
Input range
(Over range ±127%)		±0.01/0.0316/0.1/0.316/1/3.16/10/50V
Max. Input voltage±50V, ±100V at ±50V range
WeightingFLAT/A/C
HPFOFF/10/20Hz
Constant current supply28V DC/4mA
Anti-aliasing filterAnalog filter + Digital filter
LPF―
Frequency responseDC couplingDC to (Sampling Frequency/2.4)
AC coupling1kHz to (Sampling Frequency/2.4), 平坦度±0.5dB
A/D bit16/24 bit
A/D conversion method128 times over sampling Delta-sigma method
(64 times over sampling, in case of Max. sampling frequency)
Non-linearity< ±0.1%
DistortionSampling FrequencyInput rangeDistortion
96kHz, 48kHz> 0.316V< ±0.1%
< 0.1V< ±0.2%
< 24kHzAll< ±0.4%
Range accuracy< ±0.1%
SNR
(16/24 bit)
(25 deg C)		Input rangeBand
20kHz< 40kHz
0.01V64/67dB60/63dB
0.0316V74/77dB69/72dB
0.1V83/86dB77/80dB
0.316/1V87/93dB77/80dB
3.16/10/50V87/96dB77/80dB
SNR is a difference of noise level for 100% of each input range.
Dynamic range is the greatest input level and a difference of noise level of each input.
Dynamic range = SNR + 2 dB
CrosstalkInput rangeBand
20kHz< 40kHz
0.01V-64dB-60dB
0.0316V-73dB-69dB
0.1V-78dB-74dB
0.316/1/3.16/10/50V-78dB-74dB
Inter-channel phase difference< 1 deg (< 20kHz), < 3 deg (< 40kHz)
TEDSV0.9, V1.0 applicable
Input connectorBNC

Input Amp. Strain Amp.(AR-LXST100)

Input formatBalance
Input couplingDC
Input impedance1M ohm
Input range
(Over range ±127%)		DC mode: ±1/2/5/10V
ST mode: 500/1000/2000/5000/10000/20000/50000/100000μST,
Accuracy < ±1%
Max. Input voltage±25V
Gauge factor2
Applicable Gauge Resistance120 to 2000 ohm
Remote sensingAvailable
Balance range±10000μST
Balance methodBy electronic auto balance
Applicable bridgeFull bridge
Bridge methodDC
Bridge voltage2V (±1V)
10V (±5V)
Anti-aliasing filterAnalog filter + Digital filter
LPFPass/10/30/100/300/1k/3k/10k/30kHz(-3dB),
-48dB/oct 8 pole Butterworth
Frequency bandwidthDC modeDC to (Sampling Frequency/2.4), +0.5/-3dB
ST modeDC to 30kHz, ±0.5dB/-3dB
A/D bit16/24 bit
A/D conversion method128 times over sampling Delta-sigma method
(64 times over sampling, in case of Max. sampling frequency)
Non-linearity< ±0.1%
DistortionDC modesame as DC100
ST mode(SCF:10kHz, 30kHz), Sampling Frequency　24kHz,
96kHz 10000μST < 0.1%
Range accuracy< ±0.1%
SNR
(16/24 bit)
(25 deg C)		Input rangeBand
1kHz3kHz10kHz20kHz40kHz
0.25mV/V67dB62dB58dB--
0.5mV/V73dB68dB64dB--
1mV/V75dB74dB71dB--
2.5/5/10/
25/50mV/V		75dB75dB75dB--
1/2/5V---87/93dB77/83dB
SNR is a difference of noise level for 100% of each input range.
Dynamic range is the greatest input level and a difference of noise level of each input.
Dynamic range = SNR + 2 dB
CrosstalkInput rangeBand
1kHz3kHz10kHz
0.25mV/V-67dB-62dB-58dB
0.5mV/V-73dB-68dB-64dB
1mV/V-75dB-74dB-71dB
2.5/5/10/25/50mV/V-75dB-75dB-75dB
Inter-channel phase difference< 1 deg (< 20kHz), < 3 deg (< 40kHz)
Input ConnectorLemo 7-pin, 10Φ (ECGO Type)

Analog Output Amp. (AR-LXAO100)

Output formatUnbalance
Output couplingDC
Output impedance75 ohm
Output range±1 to 5V, 0.1V step
Smoothing filterAnalog filter + Digital filter
Frequency bandwidthDC to (Sampling Frequency/2.4), ±0.5dB
A/D bit16/24 bit
D/A conversion method128 times over sampling Delta-sigma method
(64 times over sampling, in case of Max. sampling frequency)
Non-linearity< ±0.1%
Distortion< ±0.2%
Range accuracy< ±0.1%
SNR
(16/24 bit)
(25 deg C)		DC Input Amp.87/93dB (in band) (at 1V input)
PA Amp.87/93dB (in band) (at 10V input)
ST Input Amp.87/93dB (in band) (DC10V input)
Crosstalk-78dB (in band < 20kHz), -75dB (in band < 40kHz)
Inter-channel phase difference< 1deg (in band < 20kHz), < 3deg (in band < 40kHz)
Input ConnectorBNC